bug [resolved]: surface iteration did not converge

Please post your Suggestion or report bugs here !

Moderators: zhej, lli5

Posts: 38
Joined: Thu Sep 22, 2011 8:44 am

bug [resolved]: surface iteration did not converge

Post by lli5 » Tue Oct 25, 2011 12:09 pm

Dear Delphi users,
Some user has reported a bug: "surface iteration did not converge"

This bug ocurrs when“scale”is set larger than 3.0, or grid is smaller than 0.3. It can be easily fixed by changing the line of "if(ndv.gt.2) then" to be "if(ndv.gt.10) then" in subroutine vwtms.

This fix will be included in the next release of Delphi.

DelPhi Development Team

Posts: 1
Joined: Thu Oct 15, 2015 1:41 am
Location: Panama City, FL

Re: bug [resolved]: surface iteration did not converge

Post by EbonyStarling » Thu Oct 15, 2015 1:47 am

Which is the current update from DelPhi? I did not have a try yet, but have a curiosity to know it. I will not get the best explanation from anywhere else other than here. Please let me know how beneficial it is for me.

Posts: 1
Joined: Fri Apr 14, 2017 5:20 am

Re: bug [resolved]: surface iteration did not converge

Post by Snelson192 » Fri Apr 14, 2017 5:24 am

Which is that the current update from Delphi? I didn't have an attempt, however, have a curiosity to understand it. I'll not get the most effective rationalization from anyplace else aside from here. Please let Pine Tree State skills helpful it's on behalf of me.

Posts: 1
Joined: Thu May 18, 2017 12:23 am

Re: bug [resolved]: surface iteration did not converge

Post by bryanadams02 » Thu May 18, 2017 12:33 am

I want to simulate air movements in a room.
I have a converge problem. Also I got this error "BiCGStab did not converge !"
in the residual page, Tdr in k-epsilon diverge. Do you know how to solve the problem?
the surface mesh quality is higher than 0.5 and volume mesh quality is higher than 0.1.
Thanks in advance for your help

Posts: 1
Joined: Sat Jun 03, 2017 12:07 am

Re: bug [resolved]: surface iteration did not converge

Post by DanielSwift » Sat Jun 03, 2017 12:20 am

This is a warning to surface chemistry solver with no converge it needs to stabilize the flow of solve surface of this to not happened that error. Mostly the residuals don’t decrease in any case that would be at high level. Most of the users cannot understand the method in which they cannot concentrate to fix all the errors after taking this smaller help.
what is online thesis help writing

Posts: 1
Joined: Fri Jun 23, 2017 5:43 am

Re: bug [resolved]: surface iteration did not converge

Post by milaarch02 » Fri Jun 23, 2017 6:03 am

Surface iteration did not converge

Posts: 1
Joined: Wed Sep 13, 2017 5:44 am
Location: India

Re: bug [resolved]: surface iteration did not converge

Post by leelachandran » Wed Sep 13, 2017 6:25 am

I am trying to model a tapering tube through which a cell moves along with the liquid. I want to study the fluid as well as the cell dynamics. I used Fluid-Structure interaction, time-dependent solver for the same. It is a fine, physics-controlled mesh. When I run the simulation, there is an error in a short while saying "Nonlinear solver did not converge." And it also says trying to find real sqrt of negative number.
When I try at finer or extremely fine mesh resolution, it says, requested mesh quality could not be achieved.
When the same simulation was carried out in an even tube, without tapering, these errors did not arise.
What could be causing the problem? How do I correct it?

Posts: 1
Joined: Thu May 24, 2018 7:29 am

Re: bug [resolved]: surface iteration did not converge

Post by ElishaGrace » Thu May 24, 2018 7:36 am

I am simulating a surface reaction in FLUENT, finite-rate.
When the iteration stats, the following error shows up:

Warning: Surface chemistry solver did not converge for 203 cells/faces

I reduced the density under-relaxation. Also, I simulated the flow alone to stabilize the flow and after that started to solve surface chemistry, but the above error happened again.
Can anyone kindly help me to resolve this issue?

Posts: 3
Joined: Mon Jun 18, 2018 8:42 am

bug resolved surface iteration did not converge

Post by MichaelRuino » Sun Jun 24, 2018 8:45 am

Try editing them through setup.txt then. Its in the same folder as the executable.
Also, the latest SVN and Binary have the menus scale according to your resolution so that their size is fixed, so if youre using those it may seem at first like the resolution doesnt change.

Actually, Zefz and Birdsey but mostly Birdsey, he did that change AFAIK, can you make this feature optional? I like my GUI and menus smaller.

Posts: 2
Joined: Sat Aug 04, 2018 2:16 am

Re: bug [resolved]: surface iteration did not converge

Post by chandu230 » Thu Aug 09, 2018 12:31 am

Visualpath is the best and Trusted training center to learn DevOps Course In Hyderabad. In Visualpath They are providing a best teaching and clear information to the students, they are Offering Real-Time Projects and practical experiments, get trained by DevOps Experts Imran teli, They are delivering now

Code: Select all

and DevOps Institute Training In Hyderabad. we are Offering Job assistance and Job Support. For More About DevOps Online Training Visit: http://www.visualpath.in/devops-online-training

Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest